| Age | Commit message (Collapse) | Author |
|
Just a refactor inside board. Activate the "ram" feature to target a
RAM-only for your given bord. I'm adding the 1170EVK RAM support.
|
|
Testing shows that we must blow fuses in order to activate either ECC
engine. Once the fuse is blown, NXP's boot ROM will enable the ECC
engine. So by the time the reset handler is running, ECC may already
be enabled.
The 32-bit copy loops won't work for initializing ITCM and OCRAM.
Since these bus widths are 64-bit and the ECC is computed over 64
bits, these 32 bit accesses result in a read-modify-write (RMW) on the
underlying interface. If these RAM regions aren't already initialized,
we'll fail an ECC check; the read in RMW compares bogus RAM contents
against a bogus ECC. This seems to dramatically slow down
initialization, or stall it (I've seen the CPU spinning in the boot
ROM).
If we listen to NXP and use 64-bit writes to preload ECC-protected RAM
regions, the 32-bit copy loops will work as expected. Note that we can
still issue 64-bit accesses towards DTCM; they're scattered across the
two 32-bit interfaces. There's an NXP whitepaper [1] describing that.
Once TCM ECC is enabled, we need to tell the TCM interfaces to RMW
smaller accesses. Otherwise, we won't generate correct ciphers. We
also might need to retry operations if there was a correction by the
RAM controller. We can perform these with predicated instructions.
Tested on an 1010EVK, where I used the debugger to show the control
registers weren't touched; and tested on the 1170EVK, with the same
approach showing the expected set bits.
[1]: https://www.nxp.com/docs/en/white-paper/CORTEXM7WP.pdf
[2]: https://www.nxp.com/docs/en/application-note/AN13204.pdf
|
|
The boot ROM is allowed to use allocations of OCRAM as scratch space. If
you interact with the boot ROM -- using it to interact with FlexSPI, for
instance -- then you cannot also use these OCRAM regions. See the system
boot chapter in the reference manual for more info.
The boot ROM typically reserves the start of OCRAM. The size varies by
chip. This commit describes a new section, .bootrom_reservation, at the
start of OCRAM. Users are encouraged to place a MaybeUninit buffer
that's sized for your ROM's requirements.
If users don't place anything in this section, then the new directive is
a no-op. On the other hand, the section is defined before other RAM
regions, so that it takes precedence over other sections users might
want to place in OCRAM.
Tested using the runtime's test suite. I'm testing with the Teensy 4
binary, since the test suite can support features in this build. The
updated test suite shows that the linker will place the boot ROM
reservation before placing the stack, suggesting that we're respecting
section priority.
|
|
To form a secondary image, use in_flash to position it in flash, then
override the default setting that disables the boot header.
With proper configuration, NXP's boot ROM can load a backup image. This
commit reconfigures the 1170EVK board for the experiment.
|
|
Just a proof-of-concept. The new inspect_elf test seems to show that
we're building the correct image. We need another commit in order to
help the program run in FlexRAM.
|
|
Applications linked through this builder can be placed in a flash
reservation. You'll need some other software to launch these programs,
since they lack the boot header required by the NXP boot ROM.
|
|
If you define a runtime, you can call `stack_size_env_override` to
define an optional environment variable checked by the runtime builder.
Same goes for the heap. A user can set these environment variables to
override the runtime's stack / heap size. You can use this package's
examples to try it out; see the updated build script.
There's no default environment variable for either memory region. The
package that defines the runtime needs to opt-in to this feature.
|
|
|